Signal strength in telecommunications

In telecommunications,[1] particularly in radio frequency engineering, signal strength refers to the transmitter power output as received by a reference antenna at a distance from the transmitting antenna. High-powered transmissions, such as those used in broadcasting, are expressed in dB-millivolts per metre (dBmV/m). For very low-power systems, such as mobile phones, signal strength is usually expressed in dB-microvolts per metre (dBμV/m) or in decibels above a reference level of one milliwatt (dBm). In broadcasting terminology, 1 mV/m is 1000 μV/m or 60 dBμ (often written dBu).

Examples
  • 100 dBμ or 100 mV/m: blanketing interference may occur on some receivers
  • 60 dBμ or 1.0 mV/m: frequently considered the edge of a radio station's protected area in North America
  • 40 dBμ or 0.1 mV/m: the minimum strength at which a station can be received with acceptable quality on most receivers

Relationship to average radiated power

edit

The electric field strength at a specific point can be determined from the power delivered to the transmitting antenna, its geometry and radiation resistance. Consider the case of a center-fed half-wave dipole antenna in free space, where the total length L is equal to one half wavelength (λ/2). If constructed from thin conductors, the current distribution is essentially sinusoidal and the radiating electric field is given by

 
Current distribution on antenna of length   equal to one half wavelength ( ).
 

where   is the angle between the antenna axis and the vector to the observation point,   is the peak current at the feed-point,   is the permittivity of free-space,   is the speed of light in vacuum, and   is the distance to the antenna in meters. When the antenna is viewed broadside ( ) the electric field is maximum and given by

 

Solving this formula for the peak current yields

 

The average power to the antenna is

 

where   is the center-fed half-wave antenna's radiation resistance. Substituting the formula for   into the one for   and solving for the maximum electric field yields

 

Therefore, if the average power to a half-wave dipole antenna is 1 mW, then the maximum electric field at 313 m (1027 ft) is 1 mV/m (60 dBμ).

For a short dipole ( ) the current distribution is nearly triangular. In this case, the electric field and radiation resistance are

 

Using a procedure similar to that above, the maximum electric field for a center-fed short dipole is

 

RF signals

edit

Although there are cell phone base station tower networks across many nations globally, there are still many areas within those nations that do not have good reception. Some rural areas are unlikely to ever be covered effectively since the cost of erecting a cell tower is too high for only a few customers. Even in areas with high signal strength, basements and the interiors of large buildings often have poor reception.

Weak signal strength can also be caused by destructive interference of the signals from local towers in urban areas, or by the construction materials used in some buildings causing significant attenuation of signal strength. Large buildings such as warehouses, hospitals and factories often have no usable signal further than a few metres from the outside walls.

This is particularly true for the networks which operate at higher frequency since these are attenuated more by intervening obstacles, although they are able to use reflection and diffraction to circumvent obstacles.

Estimated received signal strength

edit

The estimated received signal strength in an active RFID tag can be estimated as follows:

 

In general, you can take the path loss exponent into account:[2]

 
Parameter Description
dBme Estimated received power in active RFID tag
−43 Minimum received power
40 Average path loss per decade for mobile networks
r Distance mobile device - cell tower
R Mean radius of the cell tower
γ Path loss exponent

The effective path loss depends on frequency, topography, and environmental conditions.

Actually, one could use any known signal power dBm0 at any distance r0 as a reference:

 

Number of decades

edit
  would give an estimate of the number of decades, which coincides with an average path loss of 40 dB/decade.

Estimate the cell radius

edit

When we measure cell distance r and received power dBmm pairs, we can estimate the mean cell radius as follows:

 

Specialized calculation models exist to plan the location of a new cell tower, taking into account local conditions and radio equipment parameters, as well as consideration that mobile radio signals have line-of-sight propagation, unless reflection occurs.

See also

edit

References

edit
  1. ^ "Localiser un numéro de téléphone".
  2. ^ Figueiras, João; Frattasi, Simone (2010). Mobile Positioning and Tracking: From Conventional to Cooperative Techniques. John Wiley & Sons. ISBN 978-1119957560.
edit